======================== EMS-2 Firmware Revision ======================== Version 1.18 18/11/2021 (Franz Lamers) -------------------------------------- Enhancement: Added in a direct connection option to the Rotax 912iS ECU Enhancement: Menu changes for the Rotax 912iS and UL Power Version 1.17 02/09/2021 (Franz Lamers) -------------------------------------- Enhancement: Changed the hobbs minutes in the communication output to normal minutes Version 1.16 11/06/2021 (Franz Lamers) -------------------------------------- Bug: Fixed EGT/CHT display when using ULPower AUX box Version 1.15 22/04/2021 (Franz Lamers) -------------------------------------- Enhancement: Changed backlight increment to 5% and 1% below 10%. Added backlight % readout Bug: Fixed Rotax 912is Throttle position, ambient pressure, ECU hours, Engine hours Version 1.14 26/03/2021 (Franz Lamers) -------------------------------------- Enhancement: Made an automatic/manual menu item selection for the displaying of the analog channels/Volts/Map/Current section Enhancement: Cleaned up the volts on/off, numeric and bargraph displays Version 1.13 04/03/2021 (Franz Lamers) -------------------------------------- Bug: Fixed CJC showing degree F in the calibration menu Version 1.12 16/10/2020 (Franz Lamers) -------------------------------------- Enhancement: Added selection for decimal or normal hours to Hobbs Meter Version 1.11 25/08/2020 (Franz Lamers) -------------------------------------- Enhancement: Enabled Rotax 912is engine and warning messages Enhancement: Enabled Rotax 912is throttle bar graph Bug: Fixed UL Power Fuel Pressure alarm Bug: Fixed UL Power Oil/Fuel Pressure bar to psi resolution Version 1.10 20/04/2020 (Franz Lamers) -------------------------------------- Enhancement: Added Hobbs/Maintenance start selection Enhancement: General clean up Version 1.09 14/02/2020 (Franz Lamers) -------------------------------------- Enhancement: Added UMA senders N1EU70,T1EU70,N1EU70A,T1EU70A,N1EU150,T1EU150 Version 1.08 30/01/2020 (Franz Lamers) -------------------------------------- Bug: Fixed the fuel pressure voltage UMA N1EU07/T1EU07 Bar unit Enhancement: Added the UL Power Sync sensor fault message Enhancement: Added support for the UL Power Aux box Enhancement: Changed UL Power ignition status version 0 to latest version doc Enhancement: Changed UL Power MAP Pressure version 0 to latest version doc Enhancement: The current ADC values show when menu selection is over the zero and gain menu options Enhancement: Changed default current gain from 140 to 315 Version 1.07 25/09/2019 (Franz Lamers) -------------------------------------- Bug: Fixed the minimum volts causing a max values CRC error Version 1.06 05/08/2019 (Franz Lamers) -------------------------------------- Bug: Fixed CH3 and CH4 ADC values not displaying when NTC is selected for TC Channels Version 1.05 08/07/2019 (Franz Lamers) -------------------------------------- Bug: Fixed RDAC current calibration resolution when under 10A Bug: Made Analog Channels 3 and 4 = off when NTC is selected for CHT Channels Version 1.04 10/03/2019 (Franz Lamers) -------------------------------------- Enhancement: Enabled the UL Power ECU Version 1.03 04/02/2019 (Franz Lamers) -------------------------------------- Bug: Fixed fuel level averaging bug when using more then 1 tank Bug: Fixed leap year time issue Enhancement: Changed Fuel Level RDAC inputs to Channel 1->4 Bug: Fixed the ADC Value display in the USER menus Enhancement: Added in a fuel level channel to the analog channels Enhancement: Added in flight start selection between RPM1/RPM2 (Start for Hobbs/maintenance timer) Enhancement: Support added for the Rotax 912iS CAN unit Enhancement: Support added for the UL Power engine using the RS232 protocol Enhancement: Increased MAP Cal band to 75 Enhancement: Serial out analog pressure unit is set to 0.1psi Enhancement: Added fuel flow Version 1.01 16/11/2018 (Franz Lamers) -------------------------------------- Bug: Fixed the CHT been to low on the display when no EGTs are shown Enhancement: Removed the vertical silver line if only CHTs are selected Enhancement: Moved the temperature unit if only CHTs or EGTS are selected Version 1.00 28/09/2018 (Franz Lamers) -------------------------------------- Initial release